DPC Microjet

DPC Injection Cream Technical Data Sheet

Pure Cream Technology
Its unique formulation on a pure cream emulsion base enables superior penetration of the active ingredient within the building material.

Cream Consistency
The unique cream consistency allows horizontal application techniques without the injection agent running out. This combined with superior stability in the borehole ensures the optimal penetration of the active ingredient in all directions.

Effective and Safe Protection against Rising Damp
Highly effective formulation enables long lasting and deep penetration of the mortar layer creating a horizontal barrier against rising damp.

Universal Use

DPC Injection Cream allows the effective treatment of alkaline and pH neutral as well as acidic building materials.

Solvent free (VOC free)

DPC Injection Cream is free from VOC (volatile, organic compounds) classified solvents.

Environment-friendly 

DPC Injection Cream is ecologically safe and non-hazardous.

Straightforward Installation 
Efficient installation by drilling the mortar joint and filling boreholes using a low pressure sprayer or a cartridge gun. No electric DPC pump required.

Controllable and Consistent Consumption Rates 
The controlled installation technique ensures effective treatment and consistent consumption rates.

Proven Performance 
Application in practise, independent research and test reports have proven its effectiveness.
BBA Certificate No. 05/4202.

Does not form salts

Characteristic data of the product in the packaged state: 

Active ingredient content:               approx. 10% by mass
Density:                                           approx. 0.84 kg/l
Consistence:                                    cream
pH value                                          neutral
Flash point                                       > + 100°C

Range of use:

Hydrophobic impregnation of masonry against capillary rising damp using horizontal or angled borehole latest

procedures, particularly for fair faced brickwork, slim masonry layers and cleaved masonry, in- and outdoors. The mortar layer turns into a horizontal isolation. In case of higher moisture content, the Remmers patented thermal convective drying method is to be used prior to the injection procedure. Alternatively a low-pressure injection is recommended.

Working directions 

Pressureless injection 

Drill 12mm diameter holes horizontally into the mortar joint, in general into the joint intersections, at 120mm centres and to a depth of 10-20mm from opposite face. Remove bore dust from the hole and fill with DPC Injection Cream using a low pressure sprayer or a cartridge gun.

Low pressure injection 

In the low pressure procedure, the injection cream is applied into the mortar joint, in general into the joint intersections, at 120mm centres and to a depth of 10-20mm from opposite face using drive-in, resp. screw packers (metal packers) at max. 5 bar for application in a wall thickness up to 13½" and at max. bar 7 for application in a wall thickness in excess of 13½". Recommended equipment is a low pressure sprayer with suitable manometer and flowmeter.

Effect 

The capillary active building material causes the injection cream to break into a liquid phase. The silane/siloxane ingredient reacts with water and becomes a polysiloxane. During the reaction process, a silane vapour phase is produced that causes excellent penetration.

Flanking measures

Salt contaminated plasterwork should be renewed. Please ask for our recommended Funcoil 1lr Restoration Render re-plastering specification.

Tools/equipment, cleaning

a)  Drilling equipment e.g. helix drill, or SDS Plus or SDS Max drill
b)  Injection equipment, e.g. low pressure sprayer or cartridge gun
Clean tools and equipment while the material is fresh with water.

Packaging, application rate and storing:
Packaging 

310 ml and 1 litre plastic cartridges, 5 litre plastic bucket

Application rate (pressureless injection)

Wall thickness    110mm    220mm    330mm   440mm

Borehole depth     100mm    200mm    310mm    420mm

Borehole diameter 12mm      12mm       12mm      12mm

Application rate      0.9ltrs     1.9 ltrs       2.9 ltrs     3.9 ltrs
Per 10m wall
length

Application rates for porous, rubble or highly absorbent masonry may vary.

Shelf life: 

At least 1 year unopened, original stored cool but frost-free.
Storing temperature between +5°C and +25°C

Safety, ecology, disposal: 

Further information concerning safety during transport, storage and handling as well as for disposal is found in 
the Safety Data Sheet.

Technical information 

Flanking measures

Salt contaminated plasterwork should be renewed. Please ask for our recommended Funcoil 1lr Restoration Render re-plastering specification.

Tools/equipment, cleaning

a)  Drilling equipment e.g. helix drill, or SDS Plus or SDS Max drill
b)  Injection equipment, e.g. low pressure sprayer or cartridge gun

Clean tools and equipment while the material is fresh with water.

Packaging, application rate and storing:

Packaging 

310 ml and 1 litre plastic cartridges, 5 litre plastic bucket

Application rate (pressureless injection)

Wall thickness       4½"(110mm)      9"(220mm)      13½"(330mm) 18"(440mm)
Borehole depth            100mm                200mm              310mm                 420mm

Borehole diameter       12mm                  12mm                12mm                   12mm

Application rate           0.9 litres              1.9 litres            2.9 litres                3.9 litres
Per 10m wall
Length

Application rates for porous, rubble or highly absorbent masonry may vary.

Shelf life:

At least 1 year unopened, original stored cool but frost-free.
Storing temperature between +5°C and +25°C

Safety, ecology, disposal: 

Further information concerning safety during transport, storage and handling as well as for disposal is found in the latest Safety Data Sheet.